Rs. 300.00 / Hour

s your power socket loose, burnt, or not working properly? Don’t risk electrical shock or appliance damage. Sajilo Sewa provides safe and professional power socket repair and replacement services in Butwal—done by licensed electricians. Whether it’s a simple tightening or a full socket replacement, our experts restore your connection safely and efficiently. 🔧 Power Socket Repair/Replacement Includes: • Inspection of socket and wiring • Tightening or replacing loose/burnt connections • Installation of a new socket (provided by client or technician at extra cost) • Functional testing and safety check • Wall-mounted or surface-mounted sockets ✅ Service warranty for 30 days ❓ Frequently Asked Questions (FAQ) Q1: How do I know if the socket needs repair or replacement? A: Signs include sparking, loose fit, heating, or the plug not holding properly. Our technician will inspect and suggest the right solution. Q2: Can you provide the socket? A: Yes, our technician can bring a socket upon request. Material costs are additional. Q3: Is it safe for homes with old wiring? A: Yes. We inspect the wiring before starting and will inform you if a wiring upgrade is recommended. Q4: Do you offer emergency repairs? A: Yes, we offer emergency electrician services in Butwal 👉 Book now for safe and affordable power socket repair by expert electricians in Butwal

Rs. 300.00 / Hour

Worried about electrical overloads or short circuits? Installing a Single Pole MCB (Miniature Circuit Breaker) ensures your home or office is protected from sudden power surges. Sajilo Sewa offers professional SP MCB installation services across Rupandehi,Kapilvastu,Nawalparasi performed by licensed and experienced electricians. Whether you’re upgrading an old fuse or adding a new circuit for safety, we ensure secure installation with proper wiring and load testing. 🛠️ SP MCB Installation Includes: • Installation of 1 single pole MCB (6A–32A) • Wiring connection to the power source and load point • Mounting on distribution box (DB) or enclosure • Load capacity check and safety testing • Secure tightening and alignment of terminals ✅ Ideal for residential and small commercial setups ✅ 30-day service warranty ✅ Installed by certified electricians in Butwal. ❓ Frequently Asked Questions (FAQ) Q1: What is an SP MCB used for? A: It protects a single circuit from overcurrent or short circuit. Commonly used for lighting or socket protection. Q2: Can I use this service to replace an old fuse? A: Yes, we can replace your old fuse or MCB with a modern, safer SP MCB. Q3: Do you supply the MCB? A: The client can provide the MCB. We can also arrange one on request at additional cost. Q4: Is this service safe for older homes? A: Yes, we inspect the wiring before installation to ensure compatibility and safety. Q5: Will this work for emergency power circuits? A: Yes, SP MCBs are used in both normal and backup power circuits.

Rs. 300.00 / Hour

Looking to install a new power socket or replace a faulty one? Sajilo Sewa offers expert power socket fitting services in Butwal and Bhairahawa ensuring safety, functionality, and clean installation. Our electricians handle the complete process from secure mounting to safe electrical connections—ideal for homes, offices, and commercial setups. ⚙️ Power Socket Fitting Includes: • Fitting of standard or multi-pin power socket • Electrical connection from nearby point (within 1 meter) • Tightening, alignment, and safety check • Surface mounting on existing board or wall • Live testing and functionality check ✅ 30-day service warranty ❓ Frequently Asked Questions (FAQ) Q1: Will you provide the socket? A: You can either provide your own or request us to arrange one (charged separately). Q2: Can this be done on a modular board? A: Yes, we fit sockets on modular, classic, and PVC plates. Q3: Will you test the connection after fitting? A: Yes, we ensure the socket is live and working before completion. Q4: Do you offer emergency socket fitting? A: Yes, we provide emergency electrician services for urgent needs. 👉 Book now to get safe and reliable power socket fitting by certified electricians Butwal and Bhairahawa!

Rs. 2,000.00

Install by a best Refrigeration and Air Conditioning Technician who installs, maintains, and repairs cooling systems in Butwal. They have strong knowledge of refrigeration cycles, electrical systems, and inverter technologies. The best technician works with precision, safety, and efficiency, using tools like manifold gauges, multimeters, and vacuum pumps. They can diagnose faults quickly, perform accurate refrigerant charging, and ensure systems run energy-efficiently. Along with technical expertise, they maintain good communication, customer service, and cleanliness at every job site.

Rs. 100.00 / Unit

This Tihar, give your home a warm, elegant, and festive glow with Sajilo Sewa’s Nyano Light Installation Package specially designed for 3–4 storey houses in Butwal. Our expert electricians ensure safe and professional installation, so you can enjoy a cozy and hassle-free festive atmosphere. 🎇 Nyano (Warm) Light Package Includes: • 4000 Warm LED Lights for a soft and golden festive ambience • 20 Light Strips for uniform lighting coverage • 17–20 Meters Coverage per strip suitable for 3–4 storey buildings • 8 Light Combinations for beautiful lighting effects • Free Delivery & Installation • No Hidden Charges — includes all accessories such as wires, connectors, and three-pin tops •. Covers one face of a 20-foot building • Safe Installation by trained electricians following standard safety measures ❓ Frequently Asked Questions (FAQ) Q1: How long does the installation take? A: For a 3–4 storey building, installation typically takes 3–4 hours, depending on accessibility and structure. Q2: Are the lights suitable for outdoor use? A: Yes, the LED lights are weather-resistant and safe for outdoor festive decoration. Q3: Do I need to provide any materials? A: No. Everything including wires, connectors, and plugs is included in the package. Q4: Can lights be installed on multiple sides of the building? A: Yes, we can install on multiple sides at an additional charge depending on the work scope. Q5: Is there a warranty? A: Yes, we provide a 30-day service warranty to ensure your satisfaction and peace of mind. 🎆 Book your Nyano Tihar Light Installation today and let your home glow with warmth and celebration this festive season

Rs. 500.00

Best practice for Ceiling fan Replacement followed by electrician. 1. Safety First Turn off power from the main circuit breaker before starting. Use a voltage tester or multimeter to ensure there’s no live current. Wear insulated gloves and use a stable ladder. 2. Removal of Old Fan Carefully remove the fan blades one by one to reduce weight. Disconnect the canopy cover and wiring connections (note wire colors). Unscrew and remove the mounting bracket if it’s old or damaged. Check ceiling box strength — it must support the fan’s weight. 3. Inspection Before Installation Inspect wiring insulation, earthing connection, and junction box. Tighten any loose ceiling screws or anchors. Verify supply voltage (230V AC typical) and neutral/earth continuity. 4. Installing the New Fan Install the mounting bracket securely to the ceiling box. Connect wires properly: Live (brown/red) → fan switch Neutral (blue/black) → neutral terminal Earth (green/yellow) → earthing screw on the fan body Use wire connectors or insulating tape for safe joints. Hang the fan motor carefully and attach canopy covers. 5. Final Assembly and Testing Fix fan blades and ensure all screws are tight and balanced. Turn power ON and check: Smooth and quiet rotation Correct speed variation through regulator No vibration or wobbling Verify fan direction (should blow air downward in summer mode). 6. Finishing and Safety Check Clean up wiring area and tighten canopy properly. Explain operation and maintenance tips to the user. Record any warranty details or service notes.

From Rs. 1,500.00

The best and systematic process for electrical wiring fault detection — followed by professional electricians for homes or offices Near Butwal, bahirahwa and parasi 1. Safety First Turn off the main power supply before starting inspection. Use insulated tools, rubber gloves, and safety shoes. Keep a multimeter or test lamp ready for testing. 2. Visual Inspection Check for burnt smell, discolored switches, or melted insulation. Inspect loose connections in switchboards or junction boxes. Look for signs of moisture or water leakage near wiring points. 3. Power Supply Verification Turn power ON and check voltage at: Main MCB output Switchboard input terminals Sockets and points Use a multimeter or test pen to verify presence of phase (live) voltage. 4. Continuity Testing (Power OFF) Turn OFF power again. Use the continuity mode of a multimeter to check: Broken live, neutral, or earth wires Faulty switch or loose terminal Open circuit in light or socket line 5. Short Circuit or Ground Fault Detection Measure resistance between live and neutral, and live and earth. If resistance is very low → possible short circuit. Use megger (insulation tester) to test insulation resistance between wires (should be above 1 MΩ). Isolate the faulty circuit by switching off one MCB at a time to narrow down the zone. 6. Load Testing Turn ON power and connect known load (like bulb or heater). Observe if voltage drops, fuse blows, or breaker trips — this helps locate weak points or overload faults 7. Specific Fault Indicators Symptom Possible Cause No power at socket Loose wire, tripped MCB, broken neutral Repeated fuse blowing Short circuit or overload Flickering lights Loose neutral or corroded terminals Shock from appliance Faulty earthing or insulation damage Breaker tripping often Overload, short circuit, or faulty MCB 8. Final Verification After fixing the fault, recheck: Proper voltage at all outlets No spark, smell, or heat generation Earthing continuity Label the repaired circuit and document the issue for future reference.

From Rs. 500.00

Is your kitchen chimney clogged with grease, producing smoke, or making unusual noises? A poorly maintained chimney not only reduces efficiency but also poses health and fire hazards. We provide expert chimney servicing in Butwal & Bhairahawa to keep your kitchen clean, safe and smoke-free. Our Chimney Services Include: ✅Chimney Inspection & Diagnosis – Identify blockages, electrical, or mechanical issues. ✅Deep Cleaning – Removal of grease, carbon deposits, and oil build-up. ✅Filter Cleaning / Replacement – Ensures smooth airflow and better suction. ✅Motor & Fan Check-Up – To improve suction power and reduce noise. ✅Duct & Pipe Cleaning – Prevent smoke leakage and improve ventilation. ✅Installation & Uninstallation Service – Professional fitting of new chimneys or relocation of existing ones. ✅Testing & Quality Assurance – Ensure safe and efficient operation before delivery. 👉 Book your chimney servicing in Butwal & Bhairahawa today and enjoy a cleaner, smoke-free kitchen with guaranteed performance!

Rs. 500.00 / Unit

Electrician are follow the proper rules and regulation for installation of sub energy meter. which are listed in below Identify the purpose of the sub-meter (e.g., tenant billing, equipment monitoring, load analysis). Select the right type of meter: Single-phase / Three-phase (as per load) Digital / Smart / CT-operated type Class 1.0 or better accuracy for reliable readings Check voltage, current rating, and frequency compatibility with supply. Ensure the installation location is dry, well-ventilated, and accessible for reading or maintenance. 2. Safety First Turn off the main power before wiring connections. Use insulated tools and proper PPE (Personal Protective Equipment). Verify absence of voltage using a multimeter or test pen before touching conductors. Never install meters on live circuits. 3. Wiring and Connections Follow manufacturer’s wiring diagram exactly. Tighten all terminals properly to prevent overheating. Use correct wire size based on meter rating and load current. Maintain correct phase sequence (R-Y-B) and neutral polarity. For CT-operated meters: Mount CTs on the correct phase and direction (P1 → Supply, P2 → Load). Label CTs (R, Y, B) clearly. Ensure CT secondary wires are short and twisted together to reduce noise. Always short CT terminals when not connected to a meter (for safety). 4. Earthing & Protection Connect the meter body and panel to proper earthing. Use a separate MCB or fuse before the meter input for protection. Avoid parallel connections from different sources. Keep wiring neat, labeled, and segregated (power vs signal). 5. Commissioning & Testing After installation, re-energize the circuit and check: Voltage and current readings on each phase. Correct power direction (import/export). Proper display operation and communication (if smart meter). Verify meter reading with a reference meter or clamp meter. Record: Meter serial number Installation date Initial reading CT ratio and location 6. Documentation & Maintenance Keep a connection diagram and circuit label near the meter. Maintain a logbook or digital record for periodic reading. Inspect terminal tightness and seal condition regularly. Calibrate the meter periodically as per standards (e.g., ISO, NBSM).

Rs. 25.00 / Sq.Ft

This Dashain, Tihar & Chhat give your home a fresh new look with vibrant colors 🏠✨ 👉 Now at just Rs. 25 per sq.ft. ✅ Asian Paints – Apex ✅ Single Coat Primer ✅ Double Coat Paint ✅ All Materials Included 🎨 Professional finishing by an expert team – no compromise on quality! 👉 Book your Dashain Painting Service today and brighten up your home with lasting colors!

Rs. 1,500.00

Our technicians follow the procedure for EV charging installation Ensure your home has a sufficient main supply capacity (preferably single-phase 230 V or three-phase 415 V, depending on charger rating). Verify the connected load limit from your electricity provider — upgrade your meter or connection if required. Typical home chargers: Level 1: 2–3 kW (uses normal 3-pin socket, slow charging) Level 2: 7.4 kW to 11 kW (dedicated wall-mounted AC charger, faster charging. Provide a separate circuit for the EV charger — never share with other appliances. Install a dedicated MCB or RCBO (Residual Current Breaker with Overcurrent protection) for the circuit. Use a Type B RCCB / RCD for protection against DC leakage currents. Use appropriately sized copper cables (depends on charger power & distance): e.g., 6 mm² to 10 mm² for 7 kW chargers Ensure high-quality insulation (heat & moisture resistant). Keep cable runs short and protected inside PVC conduit or armored cable. Maintain correct phase, neutral, and earth connections with color coding. Ensure the home has a proper earthing system (resistance < 1 Ω ideally). Install a Surge Protection Device (SPD) to protect from voltage spikes. Always verify earth continuity from main DB to charger point. If using metal charger housing, ensure it’s earthed properly. Choose a charger with: IS/IEC standard compliance (e.g., IEC 61851, IS 17017) Overvoltage, overload, short-circuit, and earth leakage protection Smart features like load management or Wi-Fi monitoring (optional) Prefer Type 2 socket (IEC 62196) — common standard for most EVs. Weatherproof rating: IP65 or higher for outdoor installation. Select a location: Close to the parking area and power distribution board Sheltered from direct sunlight and rain With adequate ventilation and free space around the charger Mount charger at 1.2 – 1.5 m height above floor for easy access. After installation, perform: Insulation resistance test Earth continuity test Voltage and current measurement during charging Verify charging cutoff and protection operation. Clearly label the EV circuit at the main distribution board. Smart Energy Meter to track EV charging consumption. Solar integration for renewable energy charging. Automatic load balancing to avoid main breaker tripping. App-based monitoring for charging schedule and energy use.

Rs. 500.00 / Hour

A leaking wash basin faucet can be more than just annoying—it can lead to high water bills, water damage, and mold around your sink area. Whether it’s a slow drip or a steady leak, timely repair is important to avoid further damage. Sajilo Sewa provides quick and professional faucet leakage repair services for wash basins in Butwal and Bhairahawa. Our experienced plumbers visit your home, inspect the issue, and fix the faucet using proper tools and parts. We repair: • Dripping or leaking wash basin taps • Loose or worn-out washers and O-rings • Rusted or damaged faucet parts • Loose faucet joints or connections • Mixer tap or single-handle tap leaks We aim for a permanent fix with every repair. Our service includes a 30-day warranty, so you can stay stress-free.

Rs. 4,500.00 / Unit

It ensures that any fault current finds an easy path to ground, keeping both humans and electrical systems safe. Following are the points why earthing is necessary Safety from Electric Shock Protection of Electrical Equipment Stabilization of Voltage Levels Protection from Lightning and Surges Elimination of Static Charges