Rs. 500.00 / Hour

✅Inspect your mixer tap for leaks, especially around the handle, spout, and base. ✅Identify the leak's source—cartridge, O-ring, valve, or joints. ✅Turn off the water supply to the affected tap. ✅Carefully remove the tap handle with the appropriate tools. ✅Dismantle the tap body to access the internal components. ✅Inspect these components for wear, corrosion, or damage. ✅Replace any faulty parts, clean the internals, & apply plumber’s grease as needed. ✅Reassemble the tap and turn the water supply back on. ✅Check for leaks and ensure proper water flow and temperature control. ✅Make sure all fittings are secure and tidy up your work area.

Rs. 500.00 / Hour

✅Inspect the tap to identify the problem (e.g., leakage, low pressure, loose fittings, or faulty components). ✅Carefully dismantle the tap to access internal parts such as washers, cartridges, or O-rings. ✅Replace worn-out or damaged components to restore proper tap function. ✅Reassemble the tap and test for smooth operation, proper flow, and absence of leaks. ✅Clean the surrounding area and ensure the tap is securely fitted and functioning correctly.

Rs. 500.00 / Hour

✅Locate the source of the leak and inspect the waste pipe for cracks, loose joints, or corrosion. ✅Seal minor leaks with appropriate sealants or replace damaged pipe sections or fittings as needed. ✅Ensure all pipe joints are properly tightened and sealed to prevent further leakage. ✅Test the repaired section for leaks and clean the work area after completion.

Rs. 650.00 / Hour

✅Identify the cause and location of the blockage using visual checks and plumbing tools. ✅Clear debris, hair, grease, or other materials causing the blockage using plungers, drain snakes, or chemical agents. ✅Flush and clean the drainage pipes to ensure smooth water flow and prevent future clogs. ✅Test the wash basin by running water to confirm the blockage is cleared and check for any leaks. ✅Clean the work area and provide a brief report or recommendation for maintenance if needed.

Rs. 650.00 / Hour

✅Examine the plumbing system to identify the cause of the water diverter malfunction (e.g., leakage, blockage, or faulty mechanism). ✅Carefully remove the damaged diverter valve or component from the shower, faucet, or pipe system. ✅Repair the existing diverter if possible, or install a new one to restore proper water flow direction. ✅Seal all connections securely and reassemble components to prevent leaks. ✅Test the water flow to ensure the diverter functions correctly and perform a final inspection for leaks or operational issues.

Rs. 1,300.00

✅Turn off the water supply and drain any remaining water from the pipes. ✅Remove the old basin if replacing it, by disconnecting the plumbing and unscrewing the fixings. ✅Position the new basin, mark fixing points, and ensure it is level. ✅Install taps onto the basin and connect flexible water supply pipes. ✅Fit the waste and trap assembly, sealing joints with silicone to prevent leaks. ✅Secure the basin to the wall or countertop using appropriate fixings and wall plugs. ✅Connect the hot and cold water supply lines to the taps. ✅Turn the water supply back on and check for leaks in all connections. ✅Apply silicone sealant around the basin edges for a watertight finish.

Rs. 650.00 / Hour

✅Inspect the commode to locate the exact source of the leakage (tank, base, or pipe connections). ✅Turn off the water supply to prevent further leakage during the repair. ✅Check the flush valve, tank bolts, wax ring, and pipe fittings for damage or wear. ✅Replace faulty components such as seals, washers, or the wax ring. ✅Reassemble the parts, restore the water supply, and test for leaks to ensure proper sealing.

Rs. 1,500.00

✅Turn Off the Water Supply and Remove the Old Commode ✅Inspect and Prepare the Flange ✅Install Wax Ring and Position New Commode ✅Secure and Level the Commode ✅Connect the Water Supply and test the installed commode